Search results

NSI 182500 18" BLACK CABLE TI

Category: Non-Releasable Cable Ties

Bronze Ground Clamp with Adapters and Brass Screws for 0.5-1in. Pipe Heavy duty bronze ground clamp with adapters and brass screws are for bonding bare copper wire to water pipe. Assembled with brass screws.

Category: Bare Wire Ground Clamps

Cable Tie Natural Mtg Head 14" 50lb 100

Category: Non-Releasable Cable Ties

NSI 418F-ID "4"" FLAG I.D CAB

Category: Non-Releasable Cable Ties

NSI 840-6 8.5" BLUE CABLE TIE

Category: Non-Releasable Cable Ties

NSI TL250-L2 250 MCM - 1/0 AW

Category: 2-Conductor Copper Mechanical Lugs

1 HoleStandard BarrelAluminum Compression Lug2/0 AWG -3/8 Bolt Standard BarrelAluminum Compression Lugs is a type ofaluminum compression connector that is produced from high conductivityaluminum tubing.Center stop assures proper cable installation.They are tin-plated to provide corrosion resistance and are marked with die index and color coded for easy reference. Listed for 35KV maximum when properly installed.

Category: 1-Hole Aluminum Compression Lugs

NSI 8750 8 INCH BLACK CABLE T

Category: Non-Releasable Cable Ties

2 Port Heavy Duty Dual Rated Transformer Lug 350 MCM - 6 AWG Heavy Duty Dual Rated Transformer Lugs are versatile and reusable set screw connectors made from high strength 6061-T6 aluminum alloy for superior electrical and mechanical performance. Two set screws per wire hole ensure an exceptional connection. Electro-tin plated for low contact resistance. For use with copper or aluminum conductors. Mounting hole spacing is NEMA 1-3/4". Meets or exceeds ANSI C119.4 Class A. Rated 600V. Temperature rating 90 degrees C.

Category: 2-Conductor Aluminum Mechanical Lugs

NSI 840-2 8.5" RED CABLE TIE

Category: Non-Releasable Cable Ties

4 Wire Polaris 250 MCM-6 AWG Insulated Multi-Cable Connector with Mounting Holes, Either Side Wire Entry Polaris Insulated Multi-Cable Connectors have wire entry ports on both sides of the connector to allow for access from either side. Mounting holes at each end of the connector allow for direct isolated mounting to the trough, panel or wireway. IPLMD Series connectors are insulated with high-dielectric strength plastisol. Molded for precise fit and supplied with removable access plugs over the hex screws. Eliminates the need for cover and taping. Abrasion and chemical resistant. UV resistant. Will not support combustion. Mounting holes will accept a 1/4" bolt for 3/0 AWG and a 5/16" bolt for 250 MCM and 350 MCM. UL Listed 486B Wire Connector. AL9CU. Cold temperature rated to -45 degrees C, rated 600V, 90 degrees C. Dual rated for use with copper and/or aluminum cables. Not recommended for fine-stranded, flexible wire.

Category: Dual Sided Entry Wire Connector Blocks

NSI 8-350LL10 LUG 350 MCM-6 A

Category: 4-Conductor Aluminum Mechanical Lugs

Winged Wire Connector, Yellow, Easy Twist (N-Type), 22-10 AWG, Small Jar Of 100

Category: Color Coded Twist On Wire Connectors

NSI 14500-SB 14" 50LB CABLE T

Category: Non-Releasable Cable Ties

NSI IPLD3/0-4B 3/0-6 AWG POLA

Category: Dual Sided Entry Wire Connector Blocks

NSI 750-5 7.5" GREEN CABLE TI

Category: Non-Releasable Cable Ties

Dual Rated Aluminum Splice 300 MCM Dual Rated Aluminum Splices are a type of aluminum compression connector that is produced from high conductivity aluminum tubing. Center stop assures proper cable installation. Electro-tin plated for corrosion resistance. Color coded and marked with die index information. Pre-filled with oxide inhibitor and capped with color coded cap.

Category: Standard Barrel Aluminum Compression Sleeves

NSI IPLMD2505 NSIIPLMD2505

Category: Dual Sided Entry Wire Connector Blocks

Pin Terminal, Bi-Metallic, 2 AWG, 600 Volt, Material: Aluminum

Category: Copper Pigtail Adapters

Voltage Markers 120V - 208V, 1ea. 9x2.25"

Category: Voltage Markers

.250/ .125 Easy-Splice Thin Wall Tubing 48" - 1 Count Flexible flame-retardant, thin wall, general purpose heat shrinkable polyolefin tubing has a 2:1 shrink ratio. Used for electrical insulation, wire harness bundling, wire jacket marking and color coding, it also splices and makes functional terminations. Available in black, white, red, green, blue and clear. Standard packaging is either 6" lengths in blister boxes or in economical 25' spools. UL recognized to Standard 224. Black, white and colored thin wall tubing meet MIL-DTL-23053/5, Class 1. Clear meets MIL-DTL-23053/5, Class 2 and is not flame retardant. Rated 600 Volts, 125 C.

Category: Thin Wall Heat Shrink

Voltage Markers 480 Volts, 1ea. 9x2.25"

Category: Voltage Markers

Insulated Multi-Cable Connector Block, Wire Entry One Side, 600V, Number of Ports: 5, Wire Range: 350 MCM - 6 AWG, UV Rated, Abrasion and Chemical Resistant. Dual Rated for use with Copper and/or Aluminum Conductors.

Category: Single Sided Entry Wire Connector Blocks

Lay In Connector 3/0 - 6 AWG Lay-in connectors offer the ultimate in flexibility. Excellent for grounding and continuous loop applications. Made of 6061T-6 aluminum alloy. Electro-tin plated for low contact resistance. Suitable for use with both copper and aluminum conductors. Rated 600V (2000V max. per UL486B). UL 486A/B Listed. Temperature rating 90 degrees C.

Category: Aluminum Lay-In Lugs