Search results

NSI PL3/0-6 3/0-6 AWG UNINSUL

Category: Terminal Block Barrier Strips

2 Hole Long Barrel Copper Compression Lug 6 AWG - 3/8" Bolt - 1" Mounting Spacing Long Barrel Copper Compression Lugs are produced from high conductivity copper tubing. Allows easy inspection of the termination to assure complete cable insertion. Tin-plated to provide corrosion and low contact resistance. Marked with die index and color coded. Listed for 35KV maximum when properly installed. Rated 600V. cULus 486A/B Listed. UL467 Listed on sizes 6 AWG - 3/0 AWG. Temperature rating 90 degrees C.

Category: 2-Hole Long Barrel Copper Compression Lugs

NSI NPDB-26-350-1 PDB 1 POLE,

Category: Single Primary / Single Secondary Non-Insulated Distribution Blocks

3 Port Stacked Lug 800 - 300 MCM Stacked Lugs are large size set screw connectors with wire holes stacked on top of each other to minimize the width of the connector. Made of 6061T-6 aluminum alloy. Tin plated for low contact resistance. Suitable for use with both copper and aluminum conductors. Rated 600 volts (2000V max. per UL486B). UL486A/B Listed. Temperature rating 90 degrees C. Mounting hole spacing is NEMA standard of 1.75".

Category: 3-Conductor Aluminum Mechanical Lugs

NSI SP250 250 MCM SET SCREW P

Category: Single Sided Entry Wire Connector Blocks

Pre-Insulated Service Entry Sleeves 3/0 - 2 Sol Pre-insulated service entry sleeves are used for fast and easy installation with standard tools. For combinations of aluminum-aluminum and aluminum-copper conductors. Meets the requirements of ANSI C119.4. Rated 600 Volts.

Category: Standard Barrel Aluminum Compression Sleeves

Heavy Duty Direct Burial Ground Clamps for Rebar for 2.5-4in. Pipe Heavy duty direct burial ground clamps for rebar are used to connect bare copper wire to copper water pipe, ground rods and rebar for bonding. Assembled with copper alloy screws and UL Listed for direct burial in earth and concrete. Can accommodate ground wires up to 2 AWG. cULus Listed 467 Grounding and Bonding.

Category: Bare Wire Ground Clamps

Pre-Insulated Service Entry Sleeves 3/0 - 1/0 AWG Pre-insulated service entry sleeves are used for fast and easy installation with standard tools. For combinations of aluminum-aluminum and aluminum-copper conductors. Meets the requirements of ANSI C119.4. Rated 600 Volts.

Category: Standard Barrel Aluminum Compression Sleeves

Easy-Splice Direct Burial Splice Kit with Rubber Cover 14 - 2/0 AWG Direct Burial Splice Kits are dual-rated for use with copper and aluminum cable. These kits consist of an in-line mechanical set screw connector pre-filled with oxide inhibitor and an EPDM rubber insulating cover to ensure a watertight seal. Rated 600 Volts APPLICATIONS: Street lights, motor connection, irrigation systems, HVAC, outdoor lighting, and over wire connectors for a secure seal.

Category: Low Voltage Direct Burial Splice Kits

NSI 4-800LL8 LUG 800MCM-300MC

Category: 4-Conductor Aluminum Mechanical Lugs

1 HoleStandard BarrelAluminum Compression Lug3/0 AWG -3/8 Bolt Standard BarrelAluminum Compression Lugs is a type ofaluminum compression connector that is produced from high conductivityaluminum tubing.Center stop assures proper cable installation.They are tin-plated to provide corrosion resistance and are marked with die index and color coded for easy reference. Listed for 35KV maximum when properly installed.

Category: 1-Hole Aluminum Compression Lugs

Flexible Sleeve .657 I.D., 12 Per Pack

Category: Steel Crimp Connectors

NSI L4N-38 4 AWG CU COMPRESSI

Category: 2-Hole Long Barrel Copper Compression Lugs

1 HoleStandard BarrelAluminum Compression Lug750MCM -1/2 Bolt Standard BarrelAluminum Compression Lugs is a type ofaluminum compression connector that is produced from high conductivityaluminum tubing.Center stop assures proper cable installation.They are tin-plated to provide corrosion resistance and are marked with die index and color coded for easy reference. Listed for 35KV maximum when properly installed.

Category: 1-Hole Aluminum Compression Lugs

NPDB LINE 1X-750-250 - LOAD 1X750-250

Category: Single Primary / Single Secondary Non-Insulated Distribution Blocks

2-Port Black Multi-Tap Pre-Insulated Connector, 750 MCM – 1/0 AWG

Category: Dual Sided Entry Wire Connector Blocks

Long Barrel TinnedCopperSplice1 AWG Long Barrel Tinned CopperSplices is a type of copper compression connector that is produced from high conductivity copper tubing. They are tin-plated to provide corrosion resistance and are marked with die index and color coded for easy reference. Listed for 35KV maximum when properly installed.

Category: Long Barrel Copper Compression Sleeves

Easy-Splice Heat Shrinkable End Cap 4/0 AWG - 750 MCM These caps replace greases, tapes, epoxy, encapsulation, or dips. In most sizes, installation may be accomplished in less than one minute. Heat-shrinkable end caps provide for efficient and positive cable end sealing. Made of thermally stabilized polyolefin, the interior of the HSC is coated with a meltable sealant to assure a watertight seal, complete insulation, abrasion and corrosion resistance. Seals may be affected over lead, steel, aluminum, copper and all standard plastic and elastomeric insulating materials and conduit. HSC end sealing caps are qualified to ANSI C119.1-1986 and rated to ICEA electrical withstand test for 1,000 volts. HSC end sealing caps can be used as a live seal for cables carrying up to 1,000 volts. They can also be used as end seals for storing and pulling de-energized cable.

Category: Heavy Wall Heat Shrink

NSI 4-350LL6 LUG 350 MCM-6 AW

Category: 4-Conductor Aluminum Mechanical Lugs

Copper Split Bolt Connector 750 MCM Copper Split Bolt Connectors are high-strength solderless service connectors made of high-copper alloy for copper and copperweld wires. Type for two maximum wire sizes.

Category: Copper Alloy Split Bolts

NSI GLC-440DB "HEAVY DUTY GRO

Category: Bare Wire Ground Clamps

Short Barrel Copper Compression Splice for Flexible Copper Cable 300MCM Compression splices for flexible copper cables are connects that have flared openings at both ends to ensure ease of cable insertion of flexible and extra flexible cables such as locomotive, welding, mining cable and more. Positive center stop. Tin-plated for corrosion resistance. Rated 600 volts for copper cables only.

Category: Standard Barrel Copper Compression Sleeves

2HoleStandard BarrelAluminum Compression Lug 3/0 AWG -1/2 Bolt Standard BarrelAluminum Compression Lugs is a type ofaluminum compression connector that is produced from high conductivityaluminum tubing.Center stop assures proper cable installation.They are tin-plated to provide corrosion resistance and are marked with die index and color coded for easy reference. Listed for 35KV maximum when properly installed.

Category: 2-Hole Aluminum Compression Lugs

POLARIS VISION TAP 500 3 PORT SSE

Category: Single Sided Entry Wire Connector Blocks