Search results

Electronic Emergency Ballast with Backup Battery and Charger, Input Voltage: 120/277V, 90 Minute Illumination Time, 24 Hr Recharge. For use with the following 350-450 Lumen Compact, Linear & U-Bent Fluorescent Lamp Types: (1) 17-40W, 2-4 ft T8, T10, T12 or 4-Pin Long Compact

Category: Emergency Fluorescent Ballasts

Electronic Emergency Ballast with Backup Battery and Charger, Input Voltage: 120/277V, 90 Minute Illumination Time, 24 Hr Recharge. For use with the following Lamp Types: (1) Philips LED T8 InstantFit, BiPin, 8.5 - 16.5W. (designated by new Silver Can)

Category: Emergency Fluorescent Ballasts

Electronic Emergency Ballast with Backup Battery and Charger, Input Voltage: 120/277V, 90 Minute Illumination Time, 24 Hr Recharge. The B94CGU can be used with one 13 - 42 W (4-pin) twin, quad or triple twin-tube compact. It is also compatible with most one-, two-, three- and four-lamp electronic, standard, energy-saving and dimming AC ballasts

Category: Emergency Fluorescent Ballasts

10 Watt Emergency Driver for Linear LED Strips, 120-277 Volt, 90 Minute Illumination Time, Metal Case No Conduit

Category: LED Driver Emergency Power Supplies

(2) Wire Bundle Covers. For use with Emergency Ballast. ***May be required by State Law***

Category: Emergency Fluorescent Ballast Mounting Covers

4IN SQUARE STEEL BRACKET OUTLET BOX W/PIGTAIL

Category: 4" Square Metallic Boxes With Brackets

Electronic Emergency Ballast with Backup Battery and Charger, Input Voltage: 120/277V, 90 Minute Illumination Time, 24 Hr Recharge. For use with the following 600-1325 Lumen Compact, Linear & U-Bent Fluorescent Lamp Types: (1) 17-40W, 2-4 ft T5, T8, T10, T12, 4-Pin (2G11) or (1) Philips InstantFit LED T8 4' lamp

Category: Emergency Fluorescent Ballasts

LED Emergency Driver - Input Voltage: 120-277V AC. Matal Case with Conduit. Operates an LED Load of up to 10W at nominal battery voltage for a minimum of 90 minutes. Listed to UL924 and tested to CSA 22.2, No. 141 For Field or Factory Installation (Indoor and Damp) Output Class 2 Compliant **BSL310 is field installable when used with the Philips EvoKit LED Retrofit Luminaire and installed by Licensed Electrician** See pg. 6 of Wiring Diagram .pdf **

Category: LED Driver Emergency Power Supplies

Emergency Backup Inverter, Fluorescent/LED, 120/277 Volt, 90 Minute Illumination Time

Category: Emergency Fluorescent Ballasts

LED Emergency Driver - Input Voltage: 120-277V AC. Operates an LED Load of up to 10W at nominal battery voltage for a minimum of 90 minutes. UL RECOGNIZED Factory Installation * (Indoor and Damp) Output Class 2 Compliant **BSL310 is field installable when used with the Philips EvoKit LED Retrofit Luminaire and installed by Licensed Electrician** See pg. 6 of Wiring Diagram .pdf **

Category: LED Driver Emergency Power Supplies

Electronic Emergency Ballast with Backup Battery and Charger, Input Voltage: 120/277V, 90 Minute Illumination Time, 24 Hr Recharge. For use with the following 500-600 Lumen Compact, Linear & U-Bent Fluorescent Lamp Types: (1) 17-40W, 2-4 ft T8, T10, T12 or 4-Pin Long Compact.

Category: Emergency Fluorescent Ballasts

LED Emergency Driver. Input Voltage: 120/277 Volts AC, 60Hz. Output Voltage: 120/277 VAC, 60Hz. Maximum Load Power (including AC ballast/driver): 100 Watts. SINE WAVE Emergency Lighting inverter with Dimming Capabilities

Category: LED Driver Emergency Power Supplies

CUR MWSGB70794

Electronic Emergency Ballast with Backup Battery and Charger, Input Voltage: 120/277 Volt, 1000-3500 Lumens Initial Light Output, 32-215 Watt

Category: Emergency Fluorescent Ballasts

Handy Box Cover, Type: (1) Toggle Switch, Width: 2-1/8 Inch, Length: 4 Inch, Drawn, Steel

Category: Metallic Handy Box Covers

Anti-Short Bushing, Diameter 3/4 Inch, Material Non-Metallic, For Use With Cable Sizes 8-4, 6-2, 6-3, 6-4, 4-2 & 4-3 AWG

Category: Anti-Short Bushings