"wiremold"

Communication bracket with Ortronics AB2TJ TracJack and ABS2 Series II adapters included. Accepts Ortronics workstation connectivity

Category: Recessed Floor Box Service Fittings

Attaching ring for Source I (preset or afterset) zinc die-cast. 4" (102mm) O.D. 2 3/8" ring depth. Finish - Anodized Aluminum

Category: Recessed Floor Box Service Fittings

Accepts one CM2 Series communication connectivity and three Legrand AVIP or Extron Electronics MAAP Series Devices.

Category: Recessed Floor Box Service Fittings

Attaching ring for Source I (preset or afterset) zinc die-cast. 4" (102mm) O.D. 3 1/8" ring depth. Finish - Anodized Aluminum

Category: Recessed Floor Box Service Fittings

Exterior-gang pass through assembly. Designed to allow cables to pass through one (1) of the four (4) exterior-gang compartment locations.

Category: Recessed Floor Box Service Fittings

Service Fitting, 20A, Single U-Slot, Three Wire Grounded, Brass

Category: Recessed Floor Box Service Fittings

<p>Two (2) duplex KOs. One (1) plate supplied with AC8840 Box. NOTE: AC8840 is a single-service box. Power plates cannot be used in conjunction with communication plates.</p>

Category: Recessed Floor Box Service Fittings

Includes one (1) adapter to accept two (2) Extron Electronics MAAP Series devices. (Sold separately.) NOTE: For RFB2 Series Floor Boxes only.

Category: Recessed Floor Box Service Fittings

Accepts standard 15A and 20A duplex receptacles. NOTE: Standard size for device plates for Plate Location 2 is 5 7/32" (132mm) x 2 3/4" (62mm). Galvanized Steel

Category: Recessed Floor Box Service Fittings

Service Fitting, 3-1/2 Inch 20A, Material: Aluminum, Single Pedestal

Category: Recessed Floor Box Service Fittings

Hold up to five (5) devices for power, communications or audio/video. Bracket accepts EFB10 Series device plates (2 1/32" x 4 5/8") (58mm x 117mm) device plates sold separately.

Category: Recessed Floor Box Service Fittings

Exterior-gang 1 1/4" trade size conduit service feed assembly. Designed to allow connection to 1 1/4" trade size conduit feed in one (1) of the four (4) center-gang locations.

Category: Recessed Floor Box Service Fittings

Exterior-gang 3/4" trade size conduit service feed assembly. Designed to allow connection to 3/4" trade size conduit feed in one (1) of the four (4) exterior-gang locations.

Category: Recessed Floor Box Service Fittings

<p>Installed either before or after concrete pour to create activation from duct. NOTE: Drill a 2 1/2'' (64mm) hole in concrete and a 2 1/4'' (57mm) hole in duct.</p>

Category: Recessed Floor Box Service Fittings

Used to separate services in the center and outer compartments. Includes one (1) center compartment and one (1) external compartment.

Category: Recessed Floor Box Service Fittings

2" IPS locking nipple for 525 and Multiplex Series fittings. 1" long. Finish - Anodized Aluminum

Category: Recessed Floor Box Service Fittings

1" IPS locking nipple for 525 and Multiplex Series fittings. 1 1/2" long. Finish - Anodized Aluminum

Category: Recessed Floor Box Service Fittings

To convert RFB4 Box to an RFB4-4DB Box. NOTE: For RFB4 only. For use on tile, terrazzo, carpet, or wood covered floors. Additional configurations available. Please consult your local Sales Representative for more information.

Category: Recessed Floor Box Service Fittings

Prewired snap-in 20A receptacle can be wired as standard duplex or isolated ground. Available only in black. See installation instructions with replacement receptacle for complete installation details.

Category: Recessed Floor Box Service Fittings

Tunnel allows for a single service to be fed from one external compartment across the opposite external compartment while maintaining service separation.

Category: Recessed Floor Box Service Fittings

Single-gang device plate that will accept up six (6) Ortronics TracJack devices. Fits in any one (1) of the three (3) gangs in the center compartment. Devices supplied by others.

Category: Recessed Floor Box Service Fittings

<p>1/2"" (12mm) high extension. Used to increase height of preset or afterset. Die cast construction. Attach to preset or afterset with push on metal sleeves (included). Cannot be stacked.</p>

Category: Recessed Floor Box Service Fittings

Four-piece power service fitting. Duplex opening both sides. Receptacles not included. Finish - Anodized Aluminum

Category: Recessed Floor Box Service Fittings

Includes two (2) adapters to accept Ortronics TracJack devices, and two (2) adapters to accept Ortronics Series II devices (sold separately). NOTE: For RFB2 Series Floor Boxes only.

Category: Recessed Floor Box Service Fittings