"wiremold"

Slide Holder Assembly, Hole Size: 3 Inch, Available Colors: Black, Gray, Ivory, Non-Metallic Brass, and Non-Metallic Aluminum, Assembled with Scrub Water Gasket, For Use on Tile or Carpet Floors.

Category: Assembled Poke-Through Units

A 90 degree internal corner with integral dividers to provide 2" (51mm) cable bend radius for UTP and fiber optic installations. Each leg is 4 1/2" (114mm). Ideal for lay-in or pull-through installations. Finish - White

Category: 2-Piece Non-Metallic Raceway Elbows

3-Wire 125V NEMA 5-15R orange receptacle. Includes 10 1/2" [267mm] pigtails and inline splice connectors.

8" Round Cover Assembly, Evolution Series, Metallic, Cover Type: Tamper-Resistant Flush, Material/Finish: Die-Cast Aluminum/Black Powder-Coat.

Category: Poke-Through Cover Assemblies

4-1/4" Round Cover, Metallic, Cover Type: Brass or Aluminum cover plate (1/2" Opening). Device Type: Communications or Power Cover Plate. Color: Brass. For use in Carpet Applications.

Category: Round Recessed Box Covers

Poke-Through Device, Prewired, 4 Inch Diameter, (2) 20 Amp Duplex Receptacles, (10) 1-1/2 and 3/4 Inch Knockouts, NEMA 5-20R, 125 Volt, Gray

Category: Assembled Poke-Through Units

Steel, Entrance End Fitting, V2400 Series. Size: 2-11/16" Length, 1-7/8" Width, 2-1/8" Height. Includes: 1/2", 3/4" Trade Size KOs, 1/2" Trade Size KO. Black.

Category: Small 2-Piece Metallic Raceway End Fittings

90 degree internal corner, with integral dividers, that provides a 2" (51mm) cable bend radius for UTP and fiber optic installations. Ideal for lay-in or pull-through installations. Finish - White

Category: 2-Piece Non-Metallic Raceway Elbows

Aluminum, Prewired Plugmold, Tamper-Resistant, Length: 5 ft. Color: Aluminum. Outlets (6") O/C: Total Outlets: (9) 15A, 125V: Single Circuit, (1) 2-Port 2.4 USB, 5V DC, Single Outlets.

Category: Single Circuit Tamper Proof Plugmold

Eight outlets, lighted switch, rugged gray aluminum housing, 15A, 6' (1.8m) 14/3 SJT black cord with NEMA5-15 plug. Length 48" (1.2m). Receptacle center-to-center 5 1/4" (133mm). Snap-on, slide-off mounting.

Category: Work Surface Power Centers

PN5 Series Drop Ceiling Connector for dropping cables from ceiling into the raceway. Has 1/2" and 3/4" concentric trade size KOs. Includes PN153R Reducer Adapter for use with PN03 Series Raceway. Finish - Ivory

Category: 2-Piece Non-Metallic Raceway Connectors & Adapters

Two duplex receptacle brackets, receptacle insulators,power grommets, and bend radius control grommets. For use with recessed activations. Communication brackets ordered separately. Galvanized Steel

Category: Recessed Floor Box Service Fittings

One-gang pass through housing assembly. Designed to allow pass through of communication cables when no conduit is required. NOTE: When using on a 6ATCFF Furniture Feed unit, 1BHA (sold separately) is required.

Category: Poke-Through Mounting Plates

<p>Adjusting ring (with three adjusting screws) for use with 437 Attaching Rings - communication only (brass and polycarbonate fittings) and power for polycarbonate fitting only. 3 25/32'' (96mm) O.D.</p>

Category: Recessed Box Adapters

Sixteen outlets, lighted switch, rugged gray aluminum housing, 15A, 6' (1.8m) 14/3 SJT black cord with NEMA5-15 plug. Length 48" (1.2m). Receptacle center-to-center 2 1/2" (64mm). Snap-on, slide-off mounting.

Category: General Duty Power Strips

Steel, Prewired Plugmold, Length: 6 ft. Color: Gray. Outlets: (8) 15A, 120V: Single Circuit, Single Outlets.

Category: Single Circuit Steel Plugmold

Use with AMD8C Series Covers to complete installation. AMD8 Series Poke-Thru Devices require a 4" (102mm) diameter hole. Not designed to work with bare concrete or terrazzo. Floor covering thickness 1/8" minimum.

Category: Assembled Poke-Through Units

5' Steel Plugmold Multioutlet Strip with 5 duplex receptacles spaced at 12" GB Finish - Ivory

Category: Single Circuit Steel Plugmold

Cover Assembly, Surface Style, Solid, Material/Finish: Die Cast Aluminum/Bronze, No Cutouts are Provided for Floor Coverings.

Category: Round Recessed Box Covers

Steel, 90° Divided Internal Elbow, 2400 Series. Size: 1-3/4" Length, 1-29/32 Inch Height, Color: Fog White

Category: Small 2-Piece Metallic Raceway Elbows

Flanged cover for use in tile or carpet installation. Die-cast aluminum assembly. Insert in lid allows for carpet or tile cutouts to match finished floor. Finish - Nickel

Category: Square / Rectangle Recessed Box Covers

Eight (4 duplex) outlets, nonmetallic housing with ivory finish. 6' (1.8m) cord. Length 48" (1.2m). Receptacle center-to-center 12" (305mm).

Category: Single Circuit Non-Metallic Plugmold

Eight 20A, 120V, 60Hz, 2500 watt outlets, lighted switch, putty white aluminum housing, 6' (1.8m) 12/3 SJT black cord with NEMA5-20 plug. Length 17 1/4" (438mm). Receptacle center-to-center 1 1/2" (38mm). Snap-on slide-off mounting.

Category: General Duty Power Strips

<p>1/2"" (12mm) high extension. Used to increase height of preset or afterset. Die cast construction. Attach to preset or afterset with push on metal sleeves (included). Cannot be stacked.</p>

Category: Recessed Floor Box Service Fittings