Search results

Voltage Markers 120 Volts, 1ea. 9x2.25"

Category: Voltage Markers

Tap Connector for Copper to Copper, 350 MCM - 4/0 STR Main, 350 MCM - 4 SOL Tap, 600 Volt, Bronze

Category: 2-Bolt Bronze Tap Connectors

Power Distribution Block, 100kA Short Circuit Current Rated (SCCR), Finger Safe IP20 per IEC60529, DIN Rail Mount, Multi-Pole Ganging, NPDB Series PDB, SCCR RMS SYM Amps Of 100kA Rated With AL Or CU Conductors And Proper Fusing, Maximum Ampacity/Pole: 760A, 600V, 35mm DIN Rail Mountable, L: 5.80” x W: 2.75” x H: 3.75”

Category: Single Primary / Single Secondary Non-Insulated Distribution Blocks

Insulated Multi-Cable Connector Block, Wire Entry One Side, 600V, Number of Ports: 8, Wire Range: 14 AWG - 1/0 AWG, UV Rated, Abrasion and Chemical Resistant. Dual Rated for use with Copper and/or Aluminum Conductors.

Category: Single Sided Entry Wire Connector Blocks

Insulated Multi-Cable Connector Block, Wire Entry Either Side, 600V, Number of Ports: 5, Wire Range: 250 MCM - 750 MCM, UV Rated, Abrasion and Chemical Resistant. Dual Rated for use with Copper and/or Aluminum Conductors.

Category: Dual Sided Entry Wire Connector Blocks

Copper C Tap Grounding Connector for 10 to 8 AWG Copper "C" Taps ensure positive, all around compression with low-resistance and high pull-out values. Made of high conductivity copper, they satisfy the requirements of NEC250-81 and 250-91 for connecting to the grounding electrode system. Rated 600 Volts.

Category: C-Tap Press-On Lugs

Winged Wire Connector, Tan, East Twist, 22-8 AWG, Standard Jar Of 150

Category: Color Coded Twist On Wire Connectors

NSI L20N-142 2/0 AWG CU COMPR

Category: 2-Hole Long Barrel Copper Compression Lugs

insulation Piercing Connector 750-250 Main, 500-250 Tap

Category: Splices - Insulation Piercing

Aluminum Splicer Reducer 750 - 250 MCM Aluminum Splicer Reducers are used for splicing two copper or aluminum wires of equal or different sizes. Made of 6061T-6 aluminum alloy. Tin plated for low contact resistance. Suitable for use with both copper and aluminum conductors. Rated 600 volts.

Category: Aluminum Splice Reducing Lugs

16-14 Awg Fully Insulated Fem, Nylon

Category: Female Nylon Insulated Wire Disconnects

Insulated Multi-Cable Stacked Connector Block, Wire Entry Either Side, 600V, Number of Ports: 6, Wire Range: 6 AWG - 350 MCM, UV Rated, Abrasion and Chemical Resistant. Dual Rated for use with Copper and/or Aluminum Conductors.

Category: Dual Sided Entry Wire Connector Blocks

Service Post Connector - Two Wire Type 2-2 AWG Service Post Connectors is used for connecting one or two conductors. Made from high copper content hard-drawn rod. Lay-in feature makes them excellent for continuous loop grounding and bonding. Used to ground to bar or plate. Suitable for direct burial in earth or concrete.

Category: 2-Wire Service Post Connectors

Insulation Piercing Connector, Main Conductor Range: 2 AWG - 4/0 AWG, Tap Conductor Range: 4 AWG - 4/0 AWG, Voltage: 600V, Copper Current Rating: 405 Amp, Aluminum Current Rating: 315 Amp.

Category: Splices - Insulation Piercing

10 Wire Polaris 500 MCM-4 AWG Insulated Multi-Cable Connector with Mounting Holes, Either Side Wire Entry Polaris Insulated Multi-Cable Connectors have wire entry ports on both sides of the connector to allow for access from either side. Mounting holes at each end of the connector allow for direct isolated mounting to the trough, panel or wireway. IPLMD Series connectors are insulated with high-dielectric strength plastisol. Molded for precise fit and supplied with removable access plugs over the hex screws. Eliminates the need for cover and taping. Abrasion and chemical resistant. UV resistant. Will not support combustion. Mounting holes will accept a 1/4" bolt for 3/0 AWG and a 5/16" bolt for 250 MCM and 350 MCM. UL Listed 486B Wire Connector. AL9CU. Cold temperature rated to -45 degrees C, rated 600V, 90 degrees C. Dual rated for use with copper and/or aluminum cables. Not recommended for fine-stranded, flexible wire.

Category: Dual Sided Entry Wire Connector Blocks

Wet Location Twin MR-16 Emergency Light, 120/277V, (2) 7W Halogen Lamps, 6V 90Min Battery Backup

Category: Emergency Lighting - LED

Solid Pin Terminal for Copper and Aluminum Conductors 1 AWG All-aluminum Pin Terminals is designed for termination of both aluminum and copper conductors. The solid pin is made of aluminum and is tin-plated and pre-filled with oxide inhibitor. A cover is provided for quick installation. Rated 600 Volts.

Category: Aluminum Pigtail Adapters

Terminal Block, Splicer/Reducer, 3 Pole, 2-14 AWG, 75 Amp, 600 Volt, Thermal Plastic, Black

Category: Single Primary / Single Secondary Non-Insulated Distribution Blocks

NSI BTP-300 300 MCM -6 AWG AL

Category: Load Center Lug Kits

NSI FTH20A-B ADHESIVE TIE MOU

Category: Cable Tie Bases

Power Distribution Block, Large, (2) 350 MCM-6 AWG Primary (12) 4-14 AWG Secondary

Category: Double Primary / Multiple Secondary Non-Insulated Distribution Blocks

Power Distribution Block, (2) 2/0-14 AWG Primary (12) 4-14 AWG Secondary

Category: Double Primary / Multiple Secondary Non-Insulated Distribution Blocks

Dual Rated Aluminum Splice 2 AWG Dual Rated Aluminum Splices are a type of aluminum compression connector that is produced from high conductivity aluminum tubing. Center stop assures proper cable installation. Electro-tin plated for corrosion resistance. Color coded and marked with die index information. Pre-filled with oxide inhibitor and capped with color coded cap.

Category: Standard Barrel Aluminum Compression Sleeves

.500/250 Thin Wall Heat Shrink, 25 Ft Spool, 600 Volt, Round, Polyolefin, Black

Category: Thin Wall Heat Shrink