Raceway - Non-Metallic

Non-Metallic, Flexible Corduct. 1200 Series. Size: 5' Length, 2-1/2" Width, 14/32" Height. Color: Brown.

Category: Non-Metallic Overfloor Raceway

End cap fitting. Used to terminate or allow entry to T-70 raceway with conduit breakouts of 1/2" . International Gray.

Category: 1-Piece Non-Metallic Raceway End Fittings

LD2P10 Power Rated 1-piece Multi-ChannelTwo channel tamper resistant one-piece latching surface raceway. Supplied with pre-applied adhesive backed tape. Available in 8' and 10' lengths.

Category: 1-Piece Non-Metallic Raceway

Low voltage drop ceiling/entrance end fitting for use with LD3 raceway, International Gray, ABS, Length 3.42 in.

Category: 2-Piece Non-Metallic Raceway Connectors & Adapters

Optional split cover for the horizontal right angle fitting FRRA6X4YL. Snap-on feature allows cover to be installed and removed with no tools required. Creates radiused 3/4 (19mm) opening for easy access to add or remove cables.

Category: 2-Piece Non-Metallic Raceway Covers

T-45 tee fitting insert.

Category: 1-Piece Non-Metallic Raceway Tee Fittings

Attaches to 12x4 channel and/or fittings to create a 90° horizontal branch with a 4x4 exit from straight horizontal run. Accepts optional split cover FRTSC12W4BL.

Category: 1-Piece Non-Metallic Raceway Elbows

Office Furniture Raceway Communication PCommunication pole. Allows for data cable entry into office furniture raceway from suspended ceiling. 8' pole allows maximum 7' distance from top of furniture partition to ceiling. Must be used with OFR20MPT. Medium Tone.

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Reducer fitting for LD raceway from size 10 to size 3. For use with LD3 and LD10 raceway. For in-line terminations, use with CF10

Category: 1-Piece Non-Metallic Raceway Connectors & Adapters

Tee fitting for use with LDPH5 and LDS5 raceway, Electric Ivory, ABS, Length 2.58 in.

Category: 1-Piece Non-Metallic Raceway Tee Fittings

Reducer fitting for LD raceway from size 5 to size 3. For use with LD5 and LD3 raceway. For in-line terminations, use with CF5, Off White, ABS, Length 0.85 in.

Category: 1-Piece Non-Metallic Raceway Connectors & Adapters

Base coupler fitting. Used to join sections of T-70 raceway base together. International Gray.

Category: 1-Piece Non-Metallic Raceway Tee Fittings

24 x 4 end cap fitting used for closing off open ends of the channel or fittings. No coupler required. Push-on installation, Orange.

Category: 1-Piece Non-Metallic Raceway End Fittings

Outside corner fitting for use with LDPH5 and LDS5 raceway, White, ABS, Length 1.25 in.

Category: 1-Piece Non-Metallic Raceway Elbows

Entrance end fitting. Conduit breakouts of 1/2", 3/4", 1", 1 1/4" and 1 1/2" for entry from ceiling or wall. Electric Ivory.

Category: 1-Piece Non-Metallic Raceway End Fittings

Tamper resistant two-channel, one-piece latching surface raceway, PVC, White, Supplied with factory applied adhesive tape, 10' length. Color: White. Sold by foot in increments of 10.

Category: 1-Piece Non-Metallic Raceway

The FiberRunner® 4-Way Cross Channel Fitting is used in cable management to create a horizontal 4-way cross intersection with two 6 inch x 4 inch exits. It also attaches to 6x4 channels and/or fittings. The 4-way cross channel fitting accepts the optional split cover.

Category: 1-Piece Non-Metallic Raceway Connectors & Adapters

The FiberRunner® QuikLock™ Coupler is a pre-assembled coupler designed to quickly join two sections of channel and/or fittings in a cable routing system. The coupler measures 12 inches x 4 inches. No tools are required for installation.

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Attaches to 4x4 channel and/or fittings to create a 90° horizontal branch from straight horizontal runs. Accepts optional split cover FRTSC4BL.

Category: 1-Piece Non-Metallic Raceway Elbows

Attaches to 12x4 channel and/or fitting to create a 45° horizontal turn from a straight horizontal run. Accepts optional split cover FRH45SC12BL.

Category: 1-Piece Non-Metallic Raceway Elbows

Twin-70 raceway base, 8 foot length. Supplied with pre-punched mounting holes. 2' of cover needed for every 1' of Twin-70 base.

Category: 2-Piece Non-Metallic Raceway

Adapter fits into universal breakout of DCEFX or RAEFX fittings. For use LD3, LDPH3, and LDS3 raceway, Off White, PVC, Length 0.81 in.

Category: 1-Piece Non-Metallic Raceway Connectors & Adapters

Optional split cover for the four way cross fitting FRFWC6X4YL. Snap-on feature allows cover to be installed and removed with no tools required. Creates radiused 3/4 (19mm) opening for easy access to add or remove cables.

Category: 2-Piece Non-Metallic Raceway Covers

Attaches to 4x4 channel base and/or fittings to create a 90° vertical turn down from a straight horizontal run. Accepts optional split cover FROVRASC4OR.

Category: 1-Piece Non-Metallic Raceway Elbows