Raceway - Non-Metallic

Tamper resistant two-piece latching surface raceway. Supplied with pre-punched mounting holes and factory applied adhesive tape. Available in 6', 8', and 10' lengths, International Gray, Length 10.00 ft, Width 1.02 in.

Category: 2-Piece Non-Metallic Raceway

Attaches to 6x4 channel and/or fittings to create a 90° vertical turn from a straight horizontal run. Accepts optional split cover FROVRASC6YL.

Category: 1-Piece Non-Metallic Raceway Elbows

Attaches to 4x4 channel and/or fittings to create a 90° upward angle from a straight horizontal run. Used with outside vertical 90° angle fitting FROVRA4X4YL to change level of a straight horizontal run. Includes split cover.

Category: 1-Piece Non-Metallic Raceway Elbows

Entrance end fitting for LD2P10 raceway. Breakouts for 1/2" and 3/4" diameter conduit. Electric Ivory.

Category: 1-Piece Non-Metallic Raceway End Fittings

Panduct® type FS solid wall wiring duct, 2 W x 1.5 H, 6' length, PVC, white, no mounting holes.

Category: 2-Piece Non-Metallic Raceway

Tee fitting. Used to join sections of Twin-70 raceway at tee intersections, White.

Category: 1-Piece Non-Metallic Raceway Tee Fittings

Raceway Base and Cover, Above Floor, White, 6 Foot, 4-Channel

Category: 2-Piece Non-Metallic Raceway

Used to limit the bend radius of the cable to 2 (50.8mm) when exiting from 6x4 channel, 6x4 horizontal tee fitting, or 6x4 exit on 12x4 vertical tee, Black.

Category: 1-Piece Non-Metallic Raceway Tee Fittings

Attaches to 12x4 channel and/or fittings to create a horizontal four way cross intersection with two 12x4 exits. Accepts optional split cover FRFWCSC12YL.

Category: 2-Piece Non-Metallic Raceway Connectors & Adapters

Attaches to 4x4 channel and/or fitting to create a 45° upward angle from a straight horizontal run. Used with outside vertical 45° angle fitting FROV454X4OR to change level of a straight horizontal run. Includes split cover.

Category: 1-Piece Non-Metallic Raceway Elbows

Attaches to 12x4 channel and/or fittings to create a horizontal four way cross intersection with two 6x4 exits. Accepts optional split cover FRFWCSC12W6YL.

Category: 2-Piece Non-Metallic Raceway Connectors & Adapters

Optional split cover for the 6x4 FiberRunner® to 4x4 FiberRunner® Reducer Fitting FRRF6FR4BL. Snap-on feature allows cover to be installed and removed with no tools required. Creates radiused 3/4" (19mm) opening for easy access to add or remove cables.

Category: 2-Piece Non-Metallic Raceway Covers

Optional split cover for the outside vertical 45° angle fitting FROV454X4OR. Snap-on feature allows cover to be installed and removed with no tools required. Creates radiused 3/4 (19 mm) opening for easy access to add and removes cables.

Category: 2-Piece Non-Metallic Raceway Covers

Outside corner fitting. Used to join sections of Twin-70 raceway at outside corners. Electric Ivory.

Category: 2-Piece Non-Metallic Raceway Clips & Couplings

Right angle fitting. Used to join sections of TG raceway at 90° flat junctions, Electric Ivory.

Category: 2-Piece Non-Metallic Raceway Elbows

Office Furniture Raceway Snap-on VerticaSnap-on single gang vertical sloped communication faceplate. Accepts up to four PANDUIT® Mini-Com® Modules (not included). No additional mounting hardware required. TIA/EIA-606-B compliant..

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

LDS5 Solid, 1-piece Power Rated RacewayTamper resistant one-piece surface raceway. Supplied with pre-applied adhesive backed tape, International Gray, PVC, Length 10.00 ft, Width 1.01 in.

Category: 2-Piece Non-Metallic Raceway

Office Furniture Raceway Communication PCommunication pole. Allows for data cable entry into office furniture raceway from suspended ceiling. 8' pole allows maximum 7' distance from top of furniture partition to ceiling. Must be used with OFR20MPT. Office Gray.

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

4 x 4 end cap fitting used for closing off open ends of the channel or fittings. No coupler required. Push-on installation, Yellow.

Category: 1-Piece Non-Metallic Raceway End Fittings

Outside corner fitting for use with LDPH5 and LDS5 raceway, Off White, ABS, Length 1.25 in.

Category: 1-Piece Non-Metallic Raceway Elbows

Wall Duct Fitting, T-Unit, Body, 10"

Category: 2-Piece Non-Metallic Raceway Tee Fittings

Pre-assembled 24in x 4in QuikLock™ coupler quickly joins two sections of channel and/or fittings. Mechanically attaches without tightening bolts. Bolts release using 3/8in nut driver to allow coupler to be removed if necessary, Yellow, 1 piece.

Category: 2-Piece Non-Metallic Raceway Clips & Couplings

Tee fitting for use with LDPH5 and LDS5 raceway, Off White, ABS, Length 2.58 in.

Category: 1-Piece Non-Metallic Raceway Tee Fittings

Attaches to 4x4 channel and/or fittings to create a 90° vertical turn down from a straight horizontal run. Accepts optional split cover FROVRASC4YL.

Category: 1-Piece Non-Metallic Raceway Elbows