Conduit, Duct, & Raceway

For 15A and 20A decorator receptacles.

Category: Large 2-Piece Metallic Raceway Cover Plates

Wiremold 3346e Alum Single recept Cover 1.40

Category: Plugmold Covers

Tamper Resistant Two-Piece Latching Surface Raceway, Supplied With Pre-Punched Mounting Holes And Factory Applied Adhesive Tape, Available In 6', 8', and 10' Lengths, Off White, PVC, Length 10.00 ft, Width 1.02 in.

Category: 1-Piece Non-Metallic Raceway

1-1/2" Diameter, Reduced Wall Aluminum Conduit, Metallic, Lightweight Aluminum Alloy, 300 ft Reel.

Category: Flexible Aluminum Conduit

5 Inch PVC 45 Degree Sweep Elbow, 48 Inch Radius, Schedule 40, Gray, Bell End

Category: 45° PVC Sweeps

BLI B22SH-240AL Deep Strut 1 5/8

Category: Aluminum Strut with Elongated Holes

Ladder Rack, Inside Bend, Width: 18", Material/Finish: Steel/Black

Category: Cable Tray - Runway Support Kits

End cap fitting for use with LD5 raceway, White, ABS, Length 1.62 in.

Category: 1-Piece Non-Metallic Raceway End Fittings

1 Inch Red Electrical Non-Metallic Tubing (ENT), 750 Foot Reel

Category: Red ENT Conduit

Inside Corner Fitting, For Use With LDPH10 And LD2P10 Raceway, White, ABS, Length 2.49 in.

Category: 1-Piece Non-Metallic Raceway Elbows

Lay-In Galvanized Wireway, Straight Section, Screw Cover, NEMA Type 1, Dimensions: 6" x 6" x 12"

Category: Screw Cover Wireway

HOF F88T196GV WIREWAY 8X8X196

Category: Screw Cover Wireway

Cable Runway Radius Drop mounts over ladder rack cross member for bending radius when dropping cable. This Radius Drop Kit, LRD6BLK item fits 6.00 with a material of Aluminum color Black.

Category: Cable Tray Mounting Hardware

Cable Runway Triangle Support Bracket Kit supports ladder rack from a wall. This Triangle Support Bracket Kit, LTSB18BLK item fits 12 and 18 with a material of Steel color Black.

Category: Straight Cable Ladder Tray

EconoTrough protects wire and cable junctions and terminations exposed to wet conditions. This EconoTrough NEMA Type 3R, F101072RTGV item measures 10.00x10.00x72.00 inches with a material of Steel finish Galvanized.

Category: NEMA 3R Wire Trough

3 Inch Fiberglass 90 Degree Elbow, 48 Inch Radius, Black, Red Stripe

Category: Fiberglass Sweeps - 90°

Screw-Cover Wiring Trough Type 1 used for indoor applications protecting against dirt or moist. This Wiring Trough NEMA Type 1, A6612T1T item measures 6.00x6.00x12.00 inches with a material of Steel colored Gray.

Category: Screw Cover Wireway

2 Inch PVC 22-1/2 Degree Elbow, Schedule 40, Gray, Bell End

Category: Schedule 40 22-1/2° Elbows

Power Rated Drop Ceiling/Entrance End Fitting For Use With LD3, LDPH3, LDS3, LD5, LDPH5, LDS5, LD10 And LDPH10 Raceway, Use CA3 Or CA5 Adapters For LD3/LDPH3/LDS3 And LD5/LDPH5/LDS5 Profile Raceway, Adapters Not Required For LD10 And LDPH10 Raceway, White, PVC, Length 4.1 in.

Category: 1-Piece Non-Metallic Raceway End Fittings

Ladder Rack, Straight Section , Width: 12 Inches, Material/Finish: Steel/Gray

Category: Straight Cable Ladder Tray

1 in. x 100 ft. coil Enviro-Flex Liquid Tight Flexible Conduit

Category: Liquidtight Flexible Non-Metallic Conduit

Screw-Cover Wiring Trough Type 1 used for indoor applications protecting against dirt or moist. This Wiring Trough NEMA Type 1, A121224T1T item measures 12.00x12.00x24.00 inches with a material of Steel colored Gray.

Category: NEMA 1 Wire Trough

Wiring Duct Cover for 2" Duct, 6 ft Long, PVC, Gray, 30ft/box

Category: Wire Duct Covers

CDY 0503706EG RODALL THREAD3/

Category: Threaded Rod