Search results

WM C1600 6X6X120 SPECMATE WWA

Category: Hinged Cover Wireway

Entrance end fitting. Conduit breakouts of 1/2", 3/4", 1", 1 1/4" and 1 1/2" for entry from ceiling or wall. Electric Ivory.

Category: 1-Piece Non-Metallic Raceway End Fittings

Panduct® type F narrow slot wiring duct, 3 W x 1 H, 6' length, PVC, adhesive, light gray, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: High Density Wire Duct

The fiber routing 2-port spillout is used to route cable into one or two pieces of 1.5 (38mm) inside diameter split corrugated tubing. It is used with FRVT6X4YL, FRVT4X4YL, or FVT4X4YL. It is black and made of ABS plastic.

Category: Cable Tray Trapeze Hangers

Fits into LD10 breakout of most Pan-Way™ Surface Mount Outlet Boxes. For use with type PD6 raceway, Off White.

Category: Round Raceway Junction Boxes

Fits into LD10 breakout of most Pan-Way™ Surface Mount Outlet Boxes. For use with type PD3 raceway, electric ivory.

Category: Round Raceway Junction Boxes

Inside Vertical Right Angle Fitting, Fiber-Duct, Yellow

Category: Wireway Elbows

Pre-assembled coupler quickly joins two sections of hinged channel and/or fittings. Mechanically attaches without tightening bolts. Bolts release using 5/16" nut driver to allow coupler to be removed if necessary, Orange.

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

OFR20 Single Channel, Low Voltage 1-piecOne-piece single channel low voltage raceway with adhesive tape backing for data cable routing along top of modular furniture partitions. Available in 6' lengths.

Category: 1-Piece Non-Metallic Raceway Elbows

Panduct® type G wide slot wiring duct, 2.5 W x 3 H, 6' length, PVC, adhesive, light gray, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: Standard Density Wire Duct

Panduct® type G wide slot wiring duct, 2.5 W x 3 H, 6' length, PVC, adhesive, white, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: Standard Density Wire Duct

Single gang two-piece screw together extension outlet box. Box accepts Pan-Way® Screw-On Faceplates or any NEMA standard single gang faceplate. For use with Pan-Way® LD profile raceway. 4.99in L x 3.30in W x 1.00in H (126.7mm x 83.8mm x 25.4mm). Breakouts

Category: 1-Gang Raceway Device Boxes

The Wyr-Grid® Pathway Section protects cables between the Main Distribution Area and the Equipment Distribution Area. Unlike other pathways, it installs quickly and can be modified easily, optional sidewalls snap on without extra hardware or tools. Splice

Category: Straight Wire Basket

The FiberRunner® 4-Way Cross Channel Fitting is used in cable management to create a horizontal 4-way cross intersection with two 6 inch x 4 inch exits. It also attaches to 6x4 channels and/or fittings. The 4-way cross channel fitting accepts the optional split cover.

Category: Tees, Crosses & Junctions

Used to carry the cables horizontally throughout the system. Accepts hinged cable retainers FRCR4BL, hinged cover FRHC4OR2 or split hinged cover FRSHC4OR2. Use QuikLock Couplers FRBC4X4OR to attach channel and/or fittings.

Category: Straight Sections

Attaches to 4x4 channel and/or fittings to create a 45° downward angle from a horizontal run. Used with inside vertical 45° angle fitting FRIV454X4OR to change level of a straight horizontal run. Accepts optional split cover FROV45SC4OR.

Category: Elbows & Bends

Attaches any 6x4 FiberRunner® Fitting or Channel to any 4x4 FiberRunner® Fitting or Channel. Accepts split cover FRRF6FR4SCYL.

Category: End Caps & Reducers

6 x 4 end cap fitting used for closing off open ends of the channel or fittings. No coupler required. Push-on installation, Orange.

Category: End Caps & Reducers

Attaches to 12x4 channel and/or fitting to create a 45° horizontal turn from a straight horizontal run. Accepts optional split cover FRH45SC12BL.

Category: Elbows & Bends

The fiber routing spill-over junction is used to fully enclose a 6x4 channel in conjunction with the spill-over junction FRSPJ2X2YL. The cover snaps onto the channel base. A hinged feature allows easy access to add or remove cables. It is yellow and made

Category: Drop-Offs, Spillouts & Outlets

Used to carry the cables horizontally throughout the system. Accepts hinged cable retainers FRCR6BL-X, hinged cover FRHC6OR6 or split hinged cover FRSHC6OR6. Use QuikLock Coupler FRBC6X4OR to attach channel and/or fittings.

Category: Straight Sections

24 x 4 end cap fitting used for closing off open ends of the channel or fittings. No coupler required. Push-on installation, Orange.

Category: End Caps & Reducers

Optional split cover for the four way cross fitting FRFWC6X4YL. Snap-on feature allows cover to be installed and removed with no tools required. Creates radiused 3/4 (19mm) opening for easy access to add or remove cables.

Category: Tees, Crosses & Junctions

Attaches to 4x4 channel base and/or fittings to create a 90° vertical turn down from a straight horizontal run. Accepts optional split cover FROVRASC4OR.

Category: Elbows & Bends