Search results

Pre-assembled 4in x 4in QuikLock™ coupler quickly joins two sections of channel and/or fittings. Mechanically attaches without tightening bolts. Bolts release using 3/8in nut driver to allow coupler to be removed if necessary, Yellow, 20 pieces.

Category: 2-Piece Non-Metallic Raceway Clips & Couplings

TG-70 Base Coupler FittingBase coupler fitting. Each piece includes two base coupler halves for joining sections of TG-70 base together.

Category: 1-Piece Non-Metallic Raceway Tee Fittings

Office Furniture Raceway End CapEnd cap fitting. Used to terminate office furniture raceway. Supplied with adhesive tape. Office Beige.

Category: 1-Piece Non-Metallic Raceway End Fittings

Attaches to a 12x4 channel and/or fittings to create a horizontal four way cross intersection with two 4x4 exits, Black.

Category: 1-Piece Non-Metallic Raceway Elbows

Attaches to 6x4 channel and/or fittings to create a 90° upward angle from a straight horizontal run. Used with outside vertical 90° angle fitting FROVRA6X4BL to change level of a straight horizontal run. Includes split cover.

Category: 1-Piece Non-Metallic Raceway Elbows

Pre-assembled 12in x 4in QuikLock™ coupler quickly joins two sections of channel and/or fittings. Mechanically attaches without tightening bolts. Bolts release using 3/8in nut driver to allow coupler to be removed if necessary, Yellow, 1 piece.

Category: 2-Piece Non-Metallic Raceway Clips & Couplings

12 x 4 end cap fitting used for closing off open ends of the channel or fittings. No coupler required. Push-on installation, Black.

Category: 1-Piece Non-Metallic Raceway End Fittings

Single gang two-piece screw together intermediate outlet box. Box accepts Pan-Way® Screw-On Faceplates or any NEMA standard single gang faceplate. For use with Pan-Way® LD profile raceway. 5.12in L x 3.38in W x 2.27in H (130.2mm x 86.0mm x 57.7mm). Breako

Category: 1-Gang Raceway Device Boxes

OFR20 Single Channel, Low Voltage 1-piecOne-piece single channel low voltage raceway with adhesive tape backing for data cable routing along top of modular furniture partitions. Available in 8' lengths.

Category: 1-Piece Non-Metallic Raceway Elbows

Used for closing off open ends of the hinged channel or fittings. No coupler required. Push-on installation, Yellow.

Category: Wireway Closure Plates

Outside Vertical Right Angle Fitting, Fiber-Duct, Yellow

Category: Wireway Elbows

The fitting attaches any 12x4 FiberRunner® Fitting or Channel to any 6x4 FiberRunner® Fitting or Channel. It is black and made of ABS plastic. It accepts split cover FRRF126SCBL.

Category: 1-Piece Non-Metallic Raceway Elbows

Attaches to 6x4 channel and/or fittings to create a horizontal four way cross intersection. Accepts optional split cover FRFWCSC6BL.

Category: 1-Piece Non-Metallic Raceway Elbows

Single gang power rated two-piece snap together outlet box. Box accepts Pan-Way® Snap-On Faceplates. For use with Pan-Way® T-45 or LD, LDP, LDPH, LDS profile raceways. 5.00"L x 3.26"W x 1.62"H (127.1mm x 82.7mm x 41.1mm). Breakouts for 1/2", 3/4", or 1" d

Category: 1-Gang Raceway Device Boxes

Panduct® flush cover type D round hole wiring duct, 2 W x 2 H, 6' length, PVC, black, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: Standard Density Wire Duct

Snap-on single gang 106 duplex communication faceplate. Used to cover one NEMA standard 106 duplex communication module frame. Module frame screw mounts directly to underside of snap-on faceplate. No mounting device needed. Supplied with one mounting scre

Category: 1-Gang Raceway Box Covers & Faceplates

Attaches to 6x4 channel and/or fittings to create a 45° horizontal turn from a straight horizontal run. Accepts optional split cover FRH45SC6YL.

Category: 1-Piece Non-Metallic Raceway Elbows

Panduct® type FS solid wall wiring duct, 1 W x 1 H, 6' length, PVC, adhesive, white.

Category: 2-Piece Non-Metallic Raceway

Type TNC replacement cover for slotted wall wiring duct, 37.1mm cover width, 6.6' length, polyphenylene ether + high impact polystyrene (PPE + HIPS), light gray.

Category: Wire Duct Covers

2 x 2 Fiber-Duct Fitting. Attaches to channel to create a 45° downward angle from a straight horizontal run. Used with inside vertical 90° angle fitting FIVRA2X2BL or FIVRA4X4BL to change level of straight horizontal runs. Cover included.

Category: 1-Piece Non-Metallic Raceway Elbows

Panduct® type G wide slot wiring duct, 4 W x 3 H, 6' length, PVC, adhesive, white, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: Standard Density Wire Duct

Panduct® type F narrow slot wiring duct, 3 W x 5 H, 6' length, PVC, black, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: High Density Wire Duct

Panduct® type G wide slot wiring duct, 2 W x 1 H, 6' length, PVC, adhesive, white, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: Standard Density Wire Duct

Attaches any 4x4 FiberRunner® Fitting or Channel to the 2x2 Fiber-Duct™ Channel, S2X2YL6 or E2X2YL6 or 2x2 FiberRunner® Channel, HS2X2YL6 or H2X2YL6. Note: Attachment to 2x2 FiberRunner® Channel requires a QuikLock™ Coupler FBC2X2YL. Includes solid cover.

Category: 1-Piece Non-Metallic Raceway Elbows