Search results

Single gang power rated two-piece snap together outlet box. Box accepts Pan-Way® Snap-On Faceplates. For use with Pan-Way® T-45 or LD, LDP, LDPH, LDS profile raceways. 5.00"L x 3.26"W x 1.62"H (127.1mm x 82.7mm x 41.1mm). Breakouts for 1/2", 3/4", or 1" diameter conduit.

Category: 1-Gang Raceway Device Boxes

Office Furniture Raceway Right Angle FitRight angle fitting. Used to join sections of office furniture raceway at 90° flat junction. Supplied with adhesive tape, Medium Tone.

Category: 1-Piece Non-Metallic Raceway Elbows

Office Furniture Raceway 4 Way Cross FitCross fitting. Used to join sections of office furniture raceway at four corners. Supplied with adhesive tape, Office Gray.

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Office Furniture Raceway Double Spill-Over FittingDouble spill-over fitting. Fitting is used to spill over both sides of the furniture partitions at the same location. Incorporates a built-in, yet removable end cap that eliminates the need for additional raceway and fittings to terminate the pathway. Off

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Office Furniture Raceway Coupler FittingCoupler fitting. For use with office furniture raceway, Medium Tone.

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Raceway One Cubicle Drop FittingOne cubicle drop fitting. Allows the transition from office furniture raceway run horizontally along partition wall to office furniture corner raceway mounted vertically in one cubicle at the intersection of partitions. Fitting maintains 1in minimum bend

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Office Furniture Corner Raceway CoverOffice furniture corner raceway cover. Available in 6' lengths.

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Office Furniture Raceway 4 Way Cross FitCross fitting. Used to join sections of office furniture raceway at four corners. Supplied with adhesive tape, Medium Tone.

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

OFR20 Single Channel, Low Voltage 1-piecOne-piece single channel low voltage raceway with adhesive tape backing for data cable routing along top of modular furniture partitions. Available in 8' lengths.

Category: 1-Piece Non-Metallic Raceway Elbows

Long Coupler FittingLong coupler fitting (with base). Used to bridge office furniture raceway between panel sections. Can also be used to fill void left by spill-over fitting, when furniture partitions are reconfigured. Supplied with adhesive tape. Medium Tone.

Category: 1-Piece Non-Metallic Raceway Elbows

Raceway Wall Entrance FittingWall entrance fitting. Allows entry from wall to office furniture raceway run horizontally along partition walls. Fitting includes bend radius protection and trim plate to cover wall opening. Requires minimum wall opening of 4.5in W x 3.0in H (114.3mm x 7

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

4 x 4 Fiber-Duct Fitting. Attaches to channel to create a 90° horizontal turn from a straight horizontal run. Cover included. Yellow.

Category: Wireway U-Connectors

2" Corner Strip For PanelMax™ DIN Rail Wiring Duct

Category: Wire Duct Clips / Retainers

Office Furniture Corner Raceway BaseOffice furniture corner raceway base. Used to terminate low voltage data cabling in the corner at the intersection of modular office furniture panels. Accepts 70mm standard faceplates. Available in 6' lengths.

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Raceway Mid-Panel Tee FittingMid-panel tee fitting. Used to connect communication pole to office furniture raceway run horizontally along partition wall. Supplied with adhesive tape.Note: not intended for use at intersection of furniture panels. Office Gray.

Category: 1-Piece Non-Metallic Raceway Elbows

Office Furniture Raceway Inside Center FInside corner fitting. Used to join sections of office furniture raceway at inside corner. Supplied with adhesive tape. Medium Tone.

Category: 1-Piece Non-Metallic Raceway Elbows

Office Furniture Raceway Desk Mount BoxDesk mount box. Box accepts office furniture snap-on faceplates as well as 70mm NEMA standard screw-on faceplates. Designed for use with OFVR5

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Office Furniture Corner Raceway BaseOffice furniture corner raceway base. Used to terminate low voltage data cabling in the corner at the intersection of modular office furniture panels. Accepts 70mm standard faceplates. Available in 6' lengths.

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Raceway Outside Corner FittingOutside corner fitting. Used to join sections of office furniture raceway at outside corner. Supplied with adhesive tape. Medium Tone.

Category: 1-Piece Non-Metallic Raceway Elbows

Office Furniture Raceway Coupler FittingCoupler fitting. For use with office furniture raceway, Office Beige.

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Used to carry the cables vertically to the front or the back of equipment racks throughout the system. Accepts cover C2YL6. Extra supports required when used in horizontal applications. Cover sold separately, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: Special Purpose Wire Duct

Horizontal Right Angle Titting, Fiber-Duct System, Yellow

Category: Wireway Elbows

End Cap, 2 x 2 Inch, Non-Metallic, Used on Opend Ends of Channel

Category: Wireway Closure Plates

Double gang power rated two-piece snap together outlet box. Box accepts Pan-Way® Snap-On Faceplates. For use with Pan-Way® T-45 or LD profile raceway. 5.00"L x 6.14"W x 1.62"H (127.1mm x 155.9mm x 41.1mm). Breakouts for 1/2", 3/4", or 1" diameter conduit.

Category: 2-Gang Raceway Device Boxes