"wiremold"

Steel, Prewired Plugmold, Length: 6 ft. Color: Ivory. Outlets (9") O/C: Total Outlets: (8) 15A, 125V: Dual Circuit, Single Outlets

Category: Dual Circuit Steel Plugmold

Aluminum, Prewired Plugmold, Length: 6 ft. Color: Aluminum. Outlets (6") O/C: Total Outlets: (12) 15A, 125V: Single Circuit, Single Outlets.

Category: Single Circuit Aluminum Plugmold

Internal Elbow - 90°, For 2300 Series Two-Piece Raceway, For Inside Surfaces at Right Angles, Non-Metallic, White, With Integral Dividers

Category: 2-Piece Non-Metallic Raceway Elbows

Aluminum, Base, AL5200 Series. Size: 5' Length, 2" Height, 5" Width. Satin Anodized Finish. Package Quantity: 8.

Category: Large 2-Piece Metallic Raceway Bases

Right angle turns around external corners. Use with G3017TCE to offset around columns, etc. (minimum 4" (102mm) offset). Gray

Category: Large 2-Piece Metallic Raceway Elbows

Flanged Blank Cover, Die-Cast Aluminum Assembly, Flush, Finished Floor, No Cutouts, For Use in Tile or Carpet Installation, Bronze

Category: Square / Rectangle Recessed Box Covers

<p>Dual-service fitting includes housing, base, two mounting frames, divider, and mounting hardware. For use on one No. 2 and one No. 4 Duct. Has 1/2'' and 3/4'' trade size conduit knockouts on each end. 104.3 cu. in. (1709cm3) capacity.</p>

Category: Recessed Floor Box Service Fittings

For right angle turns around external corners. Integral dividers provide 2" (51mm) cable bend radius for UTP and Fiber Optic installations. Use the 5418FO for radiused alternative to 5418.

Category: 2-Piece Non-Metallic Raceway Elbows

For 90 degree tee connection at any point along a run of 6000 Series Raceway. Finish - Ivory

Category: Large 2-Piece Metallic Raceway Clips, Connectors, & Couplings

8" Round Cover Assembly, Evolution Series, Metallic, Cover Type: Tamper-Resistant Flush, Material/Finish: Die-Cast Aluminum/Gray Powder-Coat.

Category: Poke-Through Cover Assemblies

2000 Raceway Base & Cover Black û Base û 2000B .040" (1.0mm) steel. Cover û 2000C .025" (.6mm) steel. Supplied with two (2) 2010B Blank End Fittings and (1) 2001 Base Coupling. *Ordered in 5 ft internals. order 5 to get 1 base and cover*

Category: Non-Metallic Overfloor Raceway

Four-piece power service fitting. Duplex opening both sides. Receptacles not included. Finish - Anodized Aluminum

Category: Recessed Floor Box Service Fittings

Prewired snap-in 20A receptacle can be wired as standard duplexor isolated ground. Available only in black. See installation instructions with replacement receptacle for complete installation details.

Category: Assembled Poke-Through Units

Flanged cover for use in tile or carpet installation. Die-cast aluminum assembly. Insert in lid allows for carpet or tile cutouts to match finished floor. NOTE: Add suffix “TR" to the end of the part number to indicate tamper-resistant cover assembly. Tamper-resistant versions are secured with a single tamper-resistant screw. "NA" indicates North American made and complies with the Buy American Act, NAFTA, and ARRA requirements.

Category: Square / Rectangle Recessed Box Covers

Flanged cover for use in tile or carpet installation. Die-cast aluminum assembly. Lid area is flush with the finished floor, no cutouts provided. NOTE: Add suffix “TR" to the end of the part number to indicate tamper-resistant cover assembly. Tamper-resistant versions are secured with a single tamper-resistant screw. "NA" indicates North American made and complies with the Buy American Act, NAFTA, and ARRA requirements.

Category: Square / Rectangle Recessed Box Covers

Prewired snap-in 20A receptacle can be wired as standard duplex or isolated ground. Available only in black. See installation instructions with replacement receptacle for complete installation details.

Category: Recessed Floor Box Service Fittings

Non-Metallic, Prewired Plugmold, Length: 6 ft. Color: Ivory. Outlets (12") O/C: Total Outlets: (6) 15A, 125V: 2-Circuit, Duplex Outlets.

Category: Single Circuit Non-Metallic Plugmold

Nonmetallic Plugmold 5' in length with receptacles spaced 30" on center. Nonmetallic Plugmold has a textured ivory finish. For use with 20 amp circuit. Finish - Ivory

Category: Single Circuit Non-Metallic Plugmold

Poke-Through Device, Prewired, 4 Inch Diameter, (2) 20 Amp Duplex Receptacles, (10) 1-1/2 and 3/4 Inch Knockouts, NEMA 5-20R, 125 Volt, Gray

Category: Assembled Poke-Through Units

Non-Metallic, Prewired Plugmold, Length: 5 ft. Color: Ivory. Outlets (12") O/C: Total Outlets: (5) 15A, 125V: Single Circuit, Duplex Outlets.

Category: Single Circuit Non-Metallic Plugmold

Feeds 2400 and 2400D Series Raceway. Has 1/2", 3/4", and 1" trade size KOs on back and end. Removable divider and radiused insert included. Fog White

Category: Small 2-Piece Metallic Raceway End Fittings

AL5200 Series. Mounts commercially available GFCI or surge suppression receptacles. Finish - Anodized Aluminum

Category: Large 2-Piece Metallic Raceway Cover Plates

Single-gang device plate that will accept up three (3) Ortronics Series II dual modular inserts. Fits in any one (1) of the three (3) gangs in the center compartment. Devices supplied by others.

Category: Recessed Floor Box Service Fittings

Eleven 20A outlets with t-slots, 6' (1.8m) cord. Length 70" (1.8m). Receptacle center-to-center 6" (152mm). 20 Amp unit with a 20A resettable circuit breaker. Units available with straight blade or Locking Plug.

Category: Commercial Grade Power Strips