"wiremold"

For installation of two duplex style receptacles. Complete with necessary bridges.

Category: Large 2-Piece Metallic Raceway Cover Plates

1" IPS locking nipple for 525 and Multiplex Series fittings. 1 1/2" long. Finish - Anodized Aluminum

Category: Recessed Floor Box Service Fittings

Device plate that will accept up to two (2) Extron Electronics MAAP device plates. For use in either of the two side compartments only. Not for use in the center compartment. Extron devices supplied by others.

Category: Poke-Through Mounting Plates

For mounting Ortronics Series II modules into 5507 opening. Includes two outlet identification labels with clear covers and two matching screw covers. Gray

Category: 2-Piece Non-Metallic Raceway End Fittings

Accepts up to four (4) NEMA standard decorator style devices from most manufacturers.

Category: Midway & Oversized Decorator Wallplates

Twelve (6 duplex) outlets, nonmetallic housing with ivory finish. 6' (1.8m) cord. Length 48" (1.2m). Receptacle center-to-center 12" (305mm).

Category: Single Circuit Non-Metallic Plugmold

Complete cover and stem assembly. The flange is a one-piece design with one 3/4" and two 1/2" trade size conduit adapters and closure plugs. Finished color plated brass.

Category: Assembled Poke-Through Units

Flush Style Cover Assembly with Floor Insert, Tamper-Resistant, Material/Finish: Die Cast Aluminum/Black

Category: Square / Rectangle Recessed Box Covers

Use as blank cover or tap off KO in center of plate for 1/2" trade size conduit. G3007C Device Bracket included. Ivory

Category: Small 2-Piece Metallic Raceway Covers

Powder-coated aluminum power or communication plate, with 2" [51mm] and 3/4" [19.1mm] plugs. NOTE: Acceptable for use with threaded conduit when passing through power cables.

Category: Square / Rectangle Recessed Box Covers

Floor Box Assembly, Round, Type: 15 Amp Quad Receptacle, Diameter: 4 Inch, (3) 1/2 Inch Knockouts, Material/Finish: Aluminum/Aluminum, For Use in Raised Floor or Wood Floor Applications.

Category: Assembled Recessed Round Boxes

Surface Style Cover with Floor Insert, Flange, Tamper-Resistant, Material/Finish: Die Cast Aluminum/Black

Category: Square / Rectangle Recessed Box Covers

Surface Style Cover with Floor Insert, Flange, Tamper-Resistant, Material/Finish: Die Cast Aluminum/Black

Category: Square / Rectangle Recessed Box Covers

Slide Holder Assembly, Hole Size: 3 Inch, Available Colors: Black, Gray, Ivory, Non-Metallic Brass, and Non-Metallic Aluminum, Assembled with Scrub Water Gasket, For Use on Tile or Carpet Floors.

Category: Assembled Poke-Through Units

A 90 degree internal corner with integral dividers to provide 2" (51mm) cable bend radius for UTP and fiber optic installations. Each leg is 4 1/2" (114mm). Ideal for lay-in or pull-through installations. Finish - White

Category: 2-Piece Non-Metallic Raceway Elbows

.040" (1.0mm) stainless steel. S4000C-5 is available in 5' (1.5m) lengths, packed ten 5' (1.5m) lengths per carton. Also available in lengths precut to customer specifications. (Max. 5' (1.5m) lengths.)

Category: Large 2-Piece Metallic Raceway Covers

Floor Box, Rectangular, (4) Compartment, Depth: 5 Inch, 1/2 & 3/4 Inch Knockouts, Housing: Die Cast Aluminum, Black Tile Lid.

Category: Recessed Compartment Boxes

Open Architecture Device Mounting Bracket and Trim Ring. Finish - Ivory

Steel, Prewired Plugmold, 3 Foot Length, Ivory. Outlets (6") O/C: Total Outlets: (6) 20A, 125V: Single Circuit, Single Outlets.

Category: Single Circuit Steel Plugmold

<p>Installed either before or after concrete pour to create activation from duct. NOTE: Drill a 2 1/2'' (64mm) hole in concrete and a 2 1/4'' (57mm) hole in duct.</p>

Category: Recessed Floor Box Service Fittings

Floor Box, Raised 2-1/2", Size: 9-1/8 x 11 inch, Accomodates (2) Duplex Receptacles and (6) Communication Devices, Knockouts: (4) 1/2 Inch Concentric, (3) 1/2 Concentric, Polycarbonate Lid, Black

Category: Assembled Recessed Gang Boxes

Available in 3' [914mm] length with 12" spacing. USB is 2.4 Amps (shared between two ports) 5VDC. .040" [1.0mm] aluminum housing. Packed two per carton. Each unit supplied with one (1) Coupling and two (2) Blank End Fittings.

Category: Dual Circuit Steel Plugmold

8" Round Cover Assembly, Evolution Series, Metallic, Cover Type: Flush, Material/Finish: Die-Cast Aluminum/Gray Powder-Coat.

Category: Poke-Through Cover Assemblies

For hanging fixtures, smoke/fire alarms and other security devices with 3 1/2" (89mm) or 4 1/16" (103mm) mounting centers. 5 1/2" (140mm) diameter with open base. Not for use with fans. White

Category: Round Raceway Extension Boxes