1-Piece Raceway & Accessories

Attaches to 6x4 channel and/or fittings to create a horizontal four way cross intersection. Accepts optional split cover FRFWCSC6BL.

Category: 1-Piece Non-Metallic Raceway Elbows

2 x 2 Fiber-Duct Fitting. Attaches to channel to create a 45° downward angle from a straight horizontal run. Used with inside vertical 90° angle fitting FIVRA2X2BL or FIVRA4X4BL to change level of straight horizontal runs. Cover included.

Category: 1-Piece Non-Metallic Raceway Elbows

Attaches to 4x4 channel and/or fittings to create a 90° upward angle from a straight horizontal run. Used with outside vertical 90° angle fitting FROVRA4X4YL to change level of a straight horizontal run. Includes split cover.

Category: 1-Piece Non-Metallic Raceway Elbows

Used to limit the bend radius of the cable to 2 (50.8mm) when exiting from 6x4 channel, 6x4 horizontal tee fitting, or 6x4 exit on 12x4 vertical tee, Black.

Category: 1-Piece Non-Metallic Raceway Tee Fittings

Outside corner fitting. Used to join cove raceway at outside corners. Maintains a minimum 1" bend radius of cabling.

Category: 1-Piece Non-Metallic Raceway Elbows

Office Furniture Raceway Communication PCommunication pole. Allows for data cable entry into office furniture raceway from suspended ceiling. 8' pole allows maximum 7' distance from top of furniture partition to ceiling. Must be used with OFR20MPT. Office Gray.

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Office Furniture Raceway Snap-on VerticaSnap-on single gang vertical sloped communication faceplate. Accepts up to four PANDUIT® Mini-Com® Modules (not included). No additional mounting hardware required. TIA/EIA-606-B compliant..

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Outside corner fitting for use with LDPH5 and LDS5 raceway, Off White, ABS, Length 1.25 in.

Category: 1-Piece Non-Metallic Raceway Elbows

Entrance end fitting for LD2P10 raceway. Breakouts for 1/2" and 3/4" diameter conduit. Electric Ivory.

Category: 1-Piece Non-Metallic Raceway End Fittings

Tee fitting. Used to join sections of Twin-70 raceway at tee intersections, White.

Category: 1-Piece Non-Metallic Raceway Tee Fittings

4 x 4 end cap fitting used for closing off open ends of the channel or fittings. No coupler required. Push-on installation, Yellow.

Category: 1-Piece Non-Metallic Raceway End Fittings

Inside corner fitting. Used to join sections of TG raceway at inside corners. Fittings adjust from 85° to 135° to adapt to non-square corners. Electric Ivory.

Category: 1-Piece Non-Metallic Raceway Elbows

Optional split cover for the horizontal tee fitting FRT4X4YL. Snap-on feature allows cover to be installed and removed with no tools required. Creates radiused 3/4 (19mm) opening for easy access to add or remove cables.

Category: 1-Piece Non-Metallic Raceway Tee Fittings

Attaches to 4x4 channel and/or fittings to create a 90° vertical turn down from a straight horizontal run. Accepts optional split cover FROVRASC4YL.

Category: 1-Piece Non-Metallic Raceway Elbows

Coupler fitting for use with LD5, LDPH5, and LDS5 raceway, International Gray, ABS, Length 1.00 in.

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Inside Vertical 45° Fitting, for 2" x 2" Fiber-Duct, Yellow

Category: 1-Piece Non-Metallic Raceway Elbows

24 x 4 end cap fitting used for closing off open ends of the channel or fittings. No coupler required. Push-on installation, Yellow.

Category: 1-Piece Non-Metallic Raceway End Fittings

Pre-assembled coupler quickly joins two sections of hinged channel and/or fittings. Mechanically attaches without tightening bolts. Bolts release using 5/16" nut driver to allow coupler to be removed if necessary, Light Gray.

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Outside Vertical 45° Fitting, for 2" x 2" Fiber-Duct, Yellow

Category: 1-Piece Non-Metallic Raceway Elbows

Attaches to 4x4 channel and/or fittings to create a 90° vertical drop from a horizontal run. Hinged door included. Accepts FTR4X4OR, FIDT4X4BL, S4X4OR6 or E4X4OR6 directly. Accepts optional snap-on cover FRHC4OR6 in conjunction with channel.

Category: 1-Piece Non-Metallic Raceway Elbows

Attaches to 12x4 channel and/or fitting to create a 90° horizontal turn from a straight horizontal run. Inside divider walls manage cables routed around horizontal right angles. Accepts optional split cover FRRASC12YL.

Category: 1-Piece Non-Metallic Raceway Elbows

Attaches to 4x4 channel and/or fittings to create a 90° vertical drop from a horizontal run. Hinged door included. Accepts FTR4X4YL, FIDT4X4BL, S4X4YL6 or E4X4YL6 directly. Accepts optional snap-on cover FRHC4YL6 in conjunction with channel.

Category: 1-Piece Non-Metallic Raceway Elbows

Optional split cover for the horizontal tee fitting FRT6X4BL. Snap-on feature allows cover to be installed and removed with no tools required. Creates radiused 3/4 (19mm) opening for easy access to add or remove cables.

Category: 1-Piece Non-Metallic Raceway Tee Fittings

Optional split cover for the horizontal tee fitting FRT12X4BL. Snap-on feature allows cover to be installed and removed with no tools required. Creates radiused 3/4 (19mm) opening for easy access to add or remove cables.

Category: 1-Piece Non-Metallic Raceway Tee Fittings