1-Piece Raceway & Accessories

Attaches to 6x4 channel and/or fittings to create a horizontal four way cross intersection. Accepts optional split cover FRFWCSC6OR.

Category: 1-Piece Non-Metallic Raceway Elbows

Used to limit the bend radius of the cable to 2 (50.8mm) when exiting from the 12x4 channel or a 12x4 horizontal tee, Black.

Category: 1-Piece Non-Metallic Raceway Tee Fittings

Attaches to 6x4 channel and/or fittings to create a 90° upward angle from a straight horizontal run. Used with outside vertical 90° angle fitting FROVRA6X4BL to change level of a straight horizontal run. Includes split cover.

Category: 1-Piece Non-Metallic Raceway Elbows

Attaches to 4x4 channel and/or fittings to create a 45° horizontal turn from a straight horizontal run. Accepts optional split cover FRH45SC4YL.

Category: 1-Piece Non-Metallic Raceway Elbows

Office Furniture Raceway End CapEnd cap fitting. Used to terminate office furniture raceway. Supplied with adhesive tape. Office Beige.

Category: 1-Piece Non-Metallic Raceway End Fittings

Entrance end fitting for LD2P10 raceway. Breakouts for 1/2" and 3/4" diameter conduit. White.

Category: 1-Piece Non-Metallic Raceway End Fittings

2 x 2 Fiber-Duct Fitting. Attaches to channel to create a 45° downward angle from a straight horizontal run. Used with inside vertical 90° angle fitting FIVRA2X2OR or FIVRA4X4OR to change level of straight horizontal runs. Cover included.

Category: 1-Piece Non-Metallic Raceway Elbows

Attaches to 4x4 channel and/or fittings to create a 90° horizontal branch from straight horizontal runs. Accepts optional split cover FRTSC4YL.

Category: 1-Piece Non-Metallic Raceway Elbows

Reducer fitting for LD raceway from size 10 to size 5. For use with LD5 and LD10 raceway. White

Category: 1-Piece Non-Metallic Raceway Connectors & Adapters

OFR20 Single Channel, Low Voltage 1-piecOne-piece single channel low voltage raceway with adhesive tape backing for data cable routing along top of modular furniture partitions. Available in 8' lengths.

Category: 1-Piece Non-Metallic Raceway Elbows

Office Furniture Raceway Communication PCommunication pole. Allows for data cable entry into office furniture raceway from suspended ceiling. 8' pole allows maximum 7' distance from top of furniture partition to ceiling. Must be used with OFR20MPT. Office Gray.

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Attaches to 4x4 channel and/or fitting to create a 45° upward angle from a straight horizontal run. Used with outside vertical 45° angle fitting FROV454X4OR to change level of a straight horizontal run. Includes split cover.

Category: 1-Piece Non-Metallic Raceway Elbows

Attaches to 24x4 channel and/or fittings to create a horizontal four way cross intersection with two 24x4 exits. Accepts optional split cover FRFWCCV24YL.

Category: 1-Piece Non-Metallic Raceway Elbows

Attaches any 4x4 FiberRunner® Fitting or Channel to the 2x2 Fiber-Duct™ Channel, S2X2YL6 or E2X2YL6 or 2x2 FiberRunner® Channel, HS2X2YL6 or H2X2YL6. Note: Attachment to 2x2 FiberRunner® Channel requires a QuikLock™ Coupler FBC2X2YL. Includes solid cover.

Category: 1-Piece Non-Metallic Raceway Elbows

Pre-assembled 4in x 4in QuikLock™ coupler quickly joins two sections of channel and/or fittings. Mechanically attaches without tightening bolts. Bolts release using 3/8in nut driver to allow coupler to be removed if necessary, Orange, 1 piece.

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

2 x 2 Fiber-Duct Fitting. Attaches to channel to create a 45° downward angle from a straight horizontal run. Used with inside vertical 90° angle fitting FIVRA2X2LG or FIVRA4X4LG to change level of straight horizontal runs. Cover included.

Category: 1-Piece Non-Metallic Raceway Elbows

Attaches to 4x4 channel and/or fittings to create a 90° vertical drop from a horizontal run. Hinged door included. Accepts FTR4X4BL, FIDT4X4BL, S4X4BL6 or E4X4BL6 directly. Accepts optional snap-on cover FRHC4BL6 in conjunction with channel.

Category: 1-Piece Non-Metallic Raceway Elbows

The fitting attaches any 12x4 FiberRunner® Fitting or Channel to any 6x4 FiberRunner® Fitting or Channel. It is black and made of ABS plastic. It accepts split cover FRRF126SCBL.

Category: 1-Piece Non-Metallic Raceway Elbows

Attaches to 6x4 channel and/or fittings to create a horizontal four way cross intersection. Accepts optional split cover FRFWCSC6BL.

Category: 1-Piece Non-Metallic Raceway Elbows

2 x 2 Fiber-Duct Fitting. Attaches to channel to create a 45° downward angle from a straight horizontal run. Used with inside vertical 90° angle fitting FIVRA2X2BL or FIVRA4X4BL to change level of straight horizontal runs. Cover included.

Category: 1-Piece Non-Metallic Raceway Elbows

Attaches to 4x4 channel and/or fittings to create a 90° upward angle from a straight horizontal run. Used with outside vertical 90° angle fitting FROVRA4X4YL to change level of a straight horizontal run. Includes split cover.

Category: 1-Piece Non-Metallic Raceway Elbows

Used to limit the bend radius of the cable to 2 (50.8mm) when exiting from 6x4 channel, 6x4 horizontal tee fitting, or 6x4 exit on 12x4 vertical tee, Black.

Category: 1-Piece Non-Metallic Raceway Tee Fittings

Entrance end fitting for LD2P10 raceway. Breakouts for 1/2" and 3/4" diameter conduit. Electric Ivory.

Category: 1-Piece Non-Metallic Raceway End Fittings

End cap fitting. Conduit breakouts of 1/2" for entry into raceway channel. White.

Category: 1-Piece Non-Metallic Raceway End Fittings